User Guides and Installation InstructionsĮlectronic Mapping - Plug and Play Performance Note: The Hacker/Tweaker is a bare PCB board, you will need to make your own case. It powers up right from the Zt-3 DATA port. There are two mounting holes for screws or standoffs. Like all LED displays it requires a tinted foil or Lexan cover. ![]() Designed to fit into tight spots, full board dimensions are less than 2" by 1". The Zeitronix Hacker/Tweaker is a very small AFR or Lambda display for the Zt-3 Wideband Systems. Red digital AFR readout with large 0.4" (10mm) digits.High contrast display visible even in direct sunlight.Blue digital AFR readout with large 0.4" (10mm) digits.Programmable to startup as an AFR or Lambda gauge.Slim design for flexible gauge mounting options.Stylish, machined, anodized black bezel and slim enclosure.O2 Sensor Height: Plan for at least 70 mm of additional height on top of the O2 Adapter when the wideband O2 sensor is installed.įor models where clearance could be an issue, it is suggested to use the wideband bung included in the Zeitronix installation kit or find an alternative narrowband to wideband adapter such as the Innovate 12mm to 18mm O2 BUNG ADAPTER, P/N 38350 which angles the sensor to help potentially alleviate any clearance issues. O2 Adapter Height: Approximately 32 mm extending vertically when installed in the stock narrowband location. Please ensure you have adequate clearance for the adapter -AND- the O2 sensor when installed in the factory narrowband location. Please Note: This is a generic item and may not fit all makes/models due to potential clearance issues that arise from the manufacturers' designs. The Stainless Steel 12mm Narrowband Bung Bolt allows you to block off a Narrowband O2 bung allowing the Narrowband sensor to be entirely removed from the bike. This Race version of the bung bolt is light weight and has holes pre-drilled for lock wiring. The Stainless Steel Wideband Bung Bolt allows you to block off a Wideband O2 bung when the Wideband O2 sensor is not installed. ![]() You can weld this bung into exhaust systems that do not have a Wideband O2 bung. High Quality 18mm Titanium Wideband O2 Bung. High Quality 18mm Stainless Steel Wideband O2 Bung. The Extension Harness - Short is a 8 pin Molex (male) to 8 Pin Molex (female) extension harness 600mm long that allows you to extend the length of all Woolich Racing Harnesses.ġ2V Bench Flashing Power Supply with Type A Plug (USA, Canada, Japan) The Extension Harness - Long is a 8 pin Molex (male) to 8 Pin Molex (female) entension harness 1100mm long that allows you to extend the length of all Woolich Racing Harnesses. ![]() This harness allows you to connect the 2 pin plug used on our Bench Harnesses to a 12v Power Supply with a standard 2.5mm barrel connector. Note: this product requires the purchase of a Mitsubishi Interface and Bin File Definition for use with the Woolich Racing Tuned softwareīarrel to 2 Pin Plug Bench Harness Power Supply Connector Additional Bin File Definition Keys are required for each additional ECU's and can be purchased from within the WRT software. This product comes with 1 Bin File Definition Key allowing you to tune 1 ECU's as many times as you like. Secondary Throttle Plate (STP) Opening Maps.Purchase this item to gain access in the Woolich Racing Tuned software to the stock bin files for the 2004-2006 Yamaha YZF-R1.įeatures available for Yamaha YZF-R1 2004-2006 Bin File Definitions - for use in Woolich Racing Tuned softwareĢ004-2006 Yamaha YZF-R1 Stock Bin File Definitions
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |